ERW, SSAW, LSAW (UOE) difference
Conveying pipe by the different pipe process, can be divided into seamless steel tube (SML), mainly as oilfield gathering tube and small diameter internal high pressure natural gas pipeline, used for long distance oil and gas pipeline of few in number, the vast majority of long distance pipeline is to use high frequency straight seam welded pipe (ERW), spiral submerged arc welding pipe (SSAW), straight seam submerged arc welding pipe (LSAW) three. The table below for the process features of several kinds of steel pipe and quality performance contrast:
High frequency straight seam welded pipe (ERW steel pipe) according to the welding process is divided into different induction welding and resistance welding two forms, using hot rolled wide strip coil as raw material, through the continuous forming, bending, welding, heat treatment, sizing, straightening, cutting process, such as weld short compared with spiral welded pipe, high dimensional accuracy, uniform wall thickness, good surface quality, high pressure, etc. But the disadvantage is that only production of small diameter thin wall pipe, weld easy generation resistant, incomplete fusion, trench corrosion defects. Widely used such as city gas, crude oil transportation.
Spiral submerged arc welding pipe (SSAW) steel strip coil direction when the forming Angle with the center line of the pipe forming (adjustable), forming and welding, the welding seam into spiral, advantage is that the same specifications of the steel strip can produce various specifications of the steel tube diameter, raw material range is larger, the weld can avoid the principal stress, the stress condition is good, the disadvantage is that poor geometry size, weld length compared with straight seam length, easy to produce cracks, porosity, slag, weld defects such as welding, welding stress is tensile stress state. The rules and regulations of general oil and gas long distance pipeline design of spiral submerged arc welding pipe can only be used for 3, 4 regions. Abroad will improve after this process will be raw materials instead of steel plate, forming and welding, then welding and lean, cold expanding, after welding, the welding quality is close to UOE tube, at home there is no such process, is the direction of the spiral tube factory to improve in our country. "West-east gas" spiral tube is still used by traditional craft production, only the pipe hole enlargement. The United States, Japan and Germany, on the whole, negative SSAW, don't think it is proper to use SSAW trunk; Canada and Italy part use SSAW, Russia a small amount of use of SSAW, and have made a very strict complementary condition, due to historical reasons, most domestic trunk or use SSAW.
Straight seam submerged arc welding pipe (LSAW) based on single Zhang Zhonghou plate as raw material, the steel in the mold or molding machine medium-voltage (roll) into the pipe, using double-sided submerged arc welding and ChengJinHang production of hole enlargement. Its finished product specification range is wide, the toughness of the weld, plasticity, good uniformity and compactness, with large pipe diameter, wall thickness, strong resistance to high pressure, low temperature corrosion resistance, etc. In the construction of high strength, high toughness, high quality of long distance oil and gas pipeline, the steel tube are mostly straight seam submerged arc welding of large diameter thick wall pipe. According to the provisions of the API standard in large oil and gas pipelines, when the elevations, sea and city populated area in class 1, 2, straight seam submerged arc welding pipe is the only specify the applicable type. According to the forming methods of different can be divided into:
UOE welded pipe, sheet steel plate after edge bending, after U shape, O forming, welding, welding, mechanical cold expanding process;
JCOE welded pipe: according to "J - E - C - O" after welding, forming, welding process by cold hole enlargement, etc; HME welded pipe: the mandrel rolling method according to the "C - C - O" after forming, welding process by cold hole diameter, etc
2016/12/29
2016/12/28
API line pipe manufacturer
API 5L line pipe according to the production process is divided into the submerged arc welding steel pipe, etc. 8. But the main use of Seamless steel tube (Seamless), high frequency straight seam Resistance Welding steel pipe (Electric - to hold the Arc Welding, shorthand for ERW), straight seam Submerged Arc Welding pipe (Longigudinally Submerged Arc Welding, shorthand for LSAW), spiral seam Submerged Arc Welding pipe, Spirally Submerged Arc Welding, shorthand for SSAW), etc.
Straight seam submerged arc welding pipe press forming method is divided into UO (UOE), RB (RBE), JCO (JCOE), etc. The steel plate in forming mould pressing U first, then pressed into an o-ring, and then evaluated for submerged arc welding, after welding are usually at the end or span range (Expanding) called the UOE welded pipe, hole diameter is not called UO of hole diameter welded pipe. The steel plate roller bend forming (Roll Bending), and then evaluated for submerged arc welding, after welding for RBE hole diameter welded pipe or not for hole enlargement RB welded pipe. Will the steel plate according to the order of type J - C - O forming, hole enlargement of JCOE welded pipe after welding or not for hole enlargement JCO welded pipe. Of the LSAW welded pipe is a widespread use of UOE. High frequency electric resistance welded pipe ERW mainly by high frequency current skin effect and proximity effect melted the tube embryo edge, then under the action of squeezing roller pressure welding, its characteristic is no foreign filler metal, heat affected zone is small, high production efficiency. Spiral welded pipe used in long distance line SSAW pipe has a long history, is our country at present mainly adopts the line pipe.
APISPEC5L pipeline standards:
API SPEC 5 l, the American petroleum institute standards
The national standard GB/T9711 - China
2016/12/27
Coat-Plating Methods of Galvanized steel Pipes
Coat-Plating Methods of Galvanized steel Pipes
Hot dip galvanizing can protect steel pipes very well. When zinc is in liquid state, plate the steel with a thick layer of pure zinc after the complicated physical and chemical interaction and thus will make the hot dip galvanizing come into being. Also a zinc and steel alloy layer will be generated during this process. With this kind of layer and corrosion resistance feature, galvanized pipes can be applied to different severe corrosion environments, such as strong acid, alkali frog, etc., which is incomparable to other electro galvanizing.
Advantages of hot dip zinc galvanized pipes：
First, in general atmosphere, a very thin and dense layer of zinc oxide will be formed on the surface of zinc coating. It is hard to dissolve in water, therefore plays a certain protective effect to steel substrate. So, if the surface of steel pipe is covered with a quite thick and dense pure zinc layer, the steel substrate will be protected from contacting with any corrosive solution and avoid erosion.
Second, galvanized connection is very strong. When dissolving zinc and iron together, a good wear resistance will come into being and it can help the steel pipe become more strong and durable.
Third, after hot dip galvanizing, the mechanical properties of steel pipes will be improved effectively. Also, it can eliminate the stress of steel pipes in molding and welding process and benefit the lathe work.
Forth, due to the excellent ductility of zinc, its alloy layer can combine strongly with steel pipe so that plating will be protected from damage even in rolling, bending, wiredrawing, cold blanking and other molding situations.
What’s more, the surface of galvanized pipe will become bright and beautiful after the hot dip galvanizing.
2016/12/26
The comparison of ERW steel pipe and LSAW steel pipe
The comparison of ERW steel pipe and LSAW steel pipe
The ERW steel pipe Resistance is high frequency straight seam welded pipe, the English Electric hold Welding, abbreviation abbreviation for ERW, used for transporting oil, gas and vapor liquid object, can meet the requirements of high and low pressure various, currently in the field of conveying pipe in the world occupies a pivotal position.
1, welded pipe refers to the common "submerged arc welding steel pipe," marked "SC" electrical engineering, can be used as water gas pipe can also make the threading pipe, thick.
2, line pipe, wire and tube, thin, with a "T", said can only do threading works.
3, ERW pipe is "high-frequency resistance welding steel tube", unlike ordinary welded pipe welding process, welding seam is composed of steel belt ontology of parent metal melting and mechanical strength than the general welding control. "LSAW steel pipe is the main technique straight seam submerged arc welding steel pipe features: 1 steel tube forming process, the steel plate uniform deformation, residual stress is small, the surface does not produce scratches. Processing of steel pipe diameter and wall thickness of the steel pipe size range, more flexibility, especially in the production of high grade thick wall steel tube, especially in large diameter thick wall pipe has incomparable advantage over other process, can satisfy the requirement of users in the steel pipe specification more; 2 use in the process of the internal and external welding (welding) after welding process, can be in the best position for welding, is not easy to appear the wrong side, partial and incomplete fusion welding defects, such as easy to control the welding quality. 3 for overall mechanical expanding, can effectively improve the size precision of steel tube, and improve the distribution of stress in steel tube, to avoid due to the damage caused by stress corrosion, is advantageous to the field of welding construction at the same time;
4 ,to 9 100% of steel pipe quality inspection, make the whole process of steel pipe production are under effective detection, monitoring, effectively ensure the product quality.
5 ,the whole production line all equipment with the function of the computer data acquisition system networking, realize the data real-time transmission, by the central control room for production.
The ERW steel pipe Resistance is high frequency straight seam welded pipe, the English Electric hold Welding, abbreviation abbreviation for ERW, used for transporting oil, gas and vapor liquid object, can meet the requirements of high and low pressure various, currently in the field of conveying pipe in the world occupies a pivotal position.
1, welded pipe refers to the common "submerged arc welding steel pipe," marked "SC" electrical engineering, can be used as water gas pipe can also make the threading pipe, thick.
2, line pipe, wire and tube, thin, with a "T", said can only do threading works.
3, ERW pipe is "high-frequency resistance welding steel tube", unlike ordinary welded pipe welding process, welding seam is composed of steel belt ontology of parent metal melting and mechanical strength than the general welding control. "LSAW steel pipe is the main technique straight seam submerged arc welding steel pipe features: 1 steel tube forming process, the steel plate uniform deformation, residual stress is small, the surface does not produce scratches. Processing of steel pipe diameter and wall thickness of the steel pipe size range, more flexibility, especially in the production of high grade thick wall steel tube, especially in large diameter thick wall pipe has incomparable advantage over other process, can satisfy the requirement of users in the steel pipe specification more; 2 use in the process of the internal and external welding (welding) after welding process, can be in the best position for welding, is not easy to appear the wrong side, partial and incomplete fusion welding defects, such as easy to control the welding quality. 3 for overall mechanical expanding, can effectively improve the size precision of steel tube, and improve the distribution of stress in steel tube, to avoid due to the damage caused by stress corrosion, is advantageous to the field of welding construction at the same time;
4 ,to 9 100% of steel pipe quality inspection, make the whole process of steel pipe production are under effective detection, monitoring, effectively ensure the product quality.
5 ,the whole production line all equipment with the function of the computer data acquisition system networking, realize the data real-time transmission, by the central control room for production.
2016/12/25
Shinestar Won 2016 Alibaba Hundreds of Millions ISPS Award
Shinestar Won 2016 Alibaba Hundreds of Millions ISPS Award
Dec 23, 2016, looking for new foreign trade in Hunan and 2016 annual Hunan network business awards ceremony held in Changsha, about a hundred foreign trade enterprises attended the meeting, Shinestar won 2016 "Hundreds of Millions ISPS Award ", the Executive Director of Shinestar Wang Li was invited to attend and receive the award.
The awarding activity is hosted by the Kaifu District People's Government, supported by Alibaba. The activities summed up the development of 2016 Hunan foreign trade business model, commended some foreign trade enterprises' outstanding achievement in e-commerce. It has promulgated the "Annual Top Ten ISPS," "Special Contribution Award", "Ten Million ISPS Award" and "Hundreds of Millions ISPS Award " and other eight awards. Shinestar won "Hundreds of Millions ISPS Award " with excellent sales performance, as well as the special contributions to develop Hunan e-commerce, which has been warmly concerned by the on-the-spot guest.
Shinestar is based in China,service global production of large steel enterprises, is committed to global customers with high quality steel products and services.In 2016, although the environment is not good, many companies have encountered had difficulties and challenges, but Shinestar has successfully bucked the trend,Steel sales exceeded 4 billion yuan, more gains of the 2016 "Hunan top 100 enterprises "award.Behind these achievements, the role played by e-commerce is pivotal. E-commerce for Shinestar to create more business opportunities to help brands better open visibility, but also to bring effective and convenient management of the Shinestar, in terms of reducing the cost of marketing is playing a significant role.
Shinestar Steel Group CEO Wang Li said Shinestar either from capital investment or talent reserves have attached great importance to the development of E-commerce, has achieved preliminary results,2016 through the electric business platform for sales performance is proved by leaps and bounds.But e-commerce in the steel industry is still in the early stages of development, great potential, in the end how to do, how to do a good job, is a very worthy of study. Shinestar also in unceasing exploration, hope can be in the future and electricity business elite, industry experts to explore and research.
The Shinestar won "Hundreds of Millions ISPS Award " honor,both a positive result of the past, but also an encouragement for future development. Shinestar will take this as a new starting point, continue to promote the development of e-commerce, and continuously enhance the core competitiveness of enterprises.To create "century of steel enterprises in the field of overall service bench marking", and continuous efforts.
Shinestar Won 2016 Alibaba Hundreds of Millions ISPS Award
Shinestar Won 2016 Alibaba Hundreds of Millions ISPS Award
Dec 23, 2016, looking for new foreign trade in Hunan and 2016 annual Hunan network business awards ceremony held in Changsha, about a hundred foreign trade enterprises attended the meeting, Shinestar won 2016 "Hundreds of Millions ISPS Award ", the Executive Director of Shinestar Wang Li was invited to attend and receive the award.
The awarding activity is hosted by the Kaifu District People's Government, supported by Alibaba. The activities summed up the development of 2016 Hunan foreign trade business model, commended some foreign trade enterprises' outstanding achievement in e-commerce. It has promulgated the "Annual Top Ten ISPS," "Special Contribution Award", "Ten Million ISPS Award" and "Hundreds of Millions ISPS Award " and other eight awards. Shinestar won "Hundreds of Millions ISPS Award " with excellent sales performance, as well as the special contributions to develop Hunan e-commerce, which has been warmly concerned by the on-the-spot guest.
Shinestar is based in China,service global production of large steel enterprises, is committed to global customers with high quality steel products and services.In 2016, although the environment is not good, many companies have encountered had difficulties and challenges, but Shinestar has successfully bucked the trend,Steel sales exceeded 4 billion yuan, more gains of the 2016 "Hunan top 100 enterprises "award.Behind these achievements, the role played by e-commerce is pivotal. E-commerce for Shinestar to create more business opportunities to help brands better open visibility, but also to bring effective and convenient management of the Shinestar, in terms of reducing the cost of marketing is playing a significant role.
Shinestar Steel Group CEO Wang Li said Shinestar either from capital investment or talent reserves have attached great importance to the development of E-commerce, has achieved preliminary results,2016 through the electric business platform for sales performance is proved by leaps and bounds.But e-commerce in the steel industry is still in the early stages of development, great potential, in the end how to do, how to do a good job, is a very worthy of study. Shinestar also in unceasing exploration, hope can be in the future and electricity business elite, industry experts to explore and research.
The Shinestar won "Hundreds of Millions ISPS Award " honor,both a positive result of the past, but also an encouragement for future development. Shinestar will take this as a new starting point, continue to promote the development of e-commerce, and continuously enhance the core competitiveness of enterprises.To create "century of steel enterprises in the field of overall service bench marking", and continuous efforts.
2016/12/23
2016/12/22
API line pipe manufacturer
API line pipe manufacturer
Galvanized pipe using sulfate electroplating of zinc-iron alloy technology, is the production line between the slot and slot are perforated without any solution out or overflow. The production process of the process consists of the circulatory system, the tank solution that acid-base liquid, electroplating solution, the light and passivation solution, only to not use the system to leak or discharge, the production line only 5 cleaning tank, Reuse of regular emissions, in particular, after the passivation is not washed without the production of waste water production process.
Galvanized pipe using sulfate electroplating of zinc-iron alloy technology, is the production line between the slot and slot are perforated without any solution out or overflow. The production process of the process consists of the circulatory system, the tank solution that acid-base liquid, electroplating solution, the light and passivation solution, only to not use the system to leak or discharge, the production line only 5 cleaning tank, Reuse of regular emissions, in particular, after the passivation is not washed without the production of waste water production process.
2016/12/20
The Application of Galvanized Steel Pipe
The Application of Galvanized Steel Pipe
In order to improve the corrosion resistance of steel pipe, the general steel pipe galvanized. Galvanized steel sub-hot galvanized and galvanized two kinds of hot galvanized galvanized layer thickness, low cost of electro-galvanized, the surface is not very smooth. Oxygen Oxygen Welded Pipe: used for steel-making oxygen blowing pipe, the general use of small diameter welded steel pipe, specifications from 3 / 8-2 inch eight. With 08,10,15,20 or 195-Q235 made of steel, in order to prevent corrosion, and some to be effective aluminizing treatment.
Most of the old house is galvanized pipe is used, and now the kind of gas heating pipe is galvanized pipe, galvanized pipe as a water pipe, use a few years later, the tube produces a lot of rust, yellow water outflow not only Pollution, sanitary ware, but also mixed with non-smooth wall breeding bacteria, corrosion caused by heavy metal content in the water is too high, serious harm to human health. The sixties and seventies, the international developed countries began to develop new pipe, and gradually banned galvanized pipe. China's Ministry of Construction and other four ministries also issued a clear from the 2000 ban galvanized pipe, the new district of the cold water pipe has been rarely used galvanized pipe, and some of the district's hot water pipe is galvanized pipe.
2016/12/19
2016/12/18
Glavanized Steel Pipe Manufacturing
Glavanized Steel Pipe Manufacturing
Galvanized pipe using sulfate electroplating of zinc-iron alloy technology, is the production line between the slot and slot are perforated without any solution out or overflow. The production process of the process consists of the circulatory system, the tank solution that acid-base liquid, electroplating solution, the light and passivation solution, only to not use the system to leak or discharge, the production line only 5 cleaning tank, Reuse of regular emissions, in particular, after the passivation is not washed without the production of waste water production process.
Galvanized pipe using sulfate electroplating of zinc-iron alloy technology, is the production line between the slot and slot are perforated without any solution out or overflow. The production process of the process consists of the circulatory system, the tank solution that acid-base liquid, electroplating solution, the light and passivation solution, only to not use the system to leak or discharge, the production line only 5 cleaning tank, Reuse of regular emissions, in particular, after the passivation is not washed without the production of waste water production process.
Hunan Shinestar Steel Research Institute
Hunan Shinestar Steel Research Institute
If Shinestar is a ship sailing in the sea, then the company management is the captain lead the direction. In 2016, Hunan Shinestar Steel Research Institute has been founded, which is the first independent institute been set by enterprise. It will provide technical support to Shinestar to promote our company to a new level.
Hunan Shinestar Steel Research Institute belongs to the Chinese steel industry regional industry organization, will strictly follow the party's policies to service steel industry and social, adhere to innovation and development, establish and perfect industry coordination and self-discipline Mechanism to safeguard the interests of the industry as a whole and the legitimate rights and interests of enterprises. Developing our role in the industry between enterprises, and continuously improve the competitiveness of China's steel industry in the international market and promote the healthy development of the steel industry.
The service scope of Hunan Shinestar Steel Research Institute including:
Firstly, according to the relevant state policies and regulations, combined with industry characteristics, make rules for industry regulations and establish industry self-regulatory mechanism, constantly regulate the industry behavior. Especially in the promotion of industrial restructuring, elimination of backwardness, promote technological progress, strengthen energy conservation and environmental protection, improve the quality of industry operation, etc.
Secondly, carrying out industry research, participate in the development of industry development planning, industrial policies and regulations for the government and industry to strengthen macro-control and management , for policy support.
Thirdly, collecting, collating, grading release domestic and international steel industry market conditions and industry information. Monitoring the economic operation of the industry trend, to carry out special studies. Offering service to iron and steel enterprises in the management, development strategies and economic and technical indicators for analysis and evaluation.
Fourth, actively participate in the formulation, revision of the industry on technology, economy, management standards, norms, organizations to promote the implementation of member units to carry out inspection, assessment work.
Fifth, actively participate in the industry of major investment, transformation, development projects of the advanced nature, feasibility and feasibility of the early demonstration. Promote scientific and technological innovation, management innovation and product development, the development of common industry technology organizations and the promotion and application of scientific and technological achievements.
Sixth, organize sale's training, research and development trade skills, job evaluation standards and assessment, organize the steel industry vocational skills competitions, improve the professional and technical of staffs.
Seventh, actively carry out exchanges and cooperation with international organizations and overseas enterprises, keep in touch with international steel industry organizations, exchange information, negotiation, promote foreign economic and technological exchanges and cooperation, and organize companies to participate in international exhibitions.
Eighth, commissioned by the industry, according to the law to carry out the steel industry statistics, investigation, analysis and reporting and other jobs. Representation or coordination of anti-dumping, countervailing, safeguard measures related work, coordination of iron ore imports, coordination of iron and steel products import and export.
In the future, Hunan Shinestar Steel Research Institute will continue to enlarge the team, engage professors for consultancy, cooperate with domestic and foreign steel industry experts for management consulting, market research, management training, customer survey and competitor investigation. For all-round support for the wisdom of China's steel industry to contribute to the development.
2016/12/16
Technical Requirement of Galvanized Steel Pipe
Technical Requirement of Galvanized Steel Pipe
1, grades and chemical composition
Galvanized steel grades and chemical composition should be consistent with GB 3091 under the black tube steel grades and chemical composition.
2, the manufacturing method
The manufacturing method of the black tube (furnace welding or welding) is selected by the manufacturer. Galvanized by hot-dip galvanizing method.
3, thread and pipe joints
3.1 galvanized steel pipe with threaded delivery, the thread should be in galvanized after the car system. Threads shall comply with YB 822.
3.2 steel pipe joints should be consistent with the provisions of YB 238; malleable iron pipe fittings should be consistent with YB 230 requirements.
4, mechanical properties of galvanized steel pipe before the mechanical properties should be consistent with the provisions of GB 3091.
5, uniformity of galvanized galvanized steel pipe galvanized layer should be uniformity of the test. Steel pipe samples in copper sulfate solution for 5 consecutive impregnation shall not be red (copper color).
6, cold bending test Nominal diameter of not more than 50mm galvanized steel pipe should be cold bending test. Bending angle of 90 °, bending radius of 8 times the diameter. Test with no filler, the specimen weld should be placed in the bending direction of the outer or upper. After the test, the sample should not have cracks and zinc peeling off the same.
7, water pressure test Water pressure test should be carried out in the black, eddy current testing can also be used instead of water pressure test. Test pressure or eddy current inspection shall be in accordance with GB 3092 for the size of the reference sample.
2016/12/09
2016/12/08
Carbon Steel Pipe Production
Carbon steel pipe can be divided into seamless steel pipe, straight seam steel pipe, spiral steel pipe, high-frequency welded steel pipe. Rolled seamless carbon steel pipe is the raw material of round tube, tube embryo to be cut through the cutting machine into a length of about 1 m of blank, and the conveyor belt to the furnace heating. The billet is fed into a furnace and heated at a temperature of about 1200 degrees Celsius. The fuel is hydrogen or acetylene. Furnace temperature control is a key issue. After the round tube billet to go through the pressure piercing machine to wear empty. Generally more common punching machine is conical roller piercing machine, this punching machine production efficiency is high, product quality is good, perforation expansion diameter large, can wear a variety of steel. After piercing, the round tube blank has been three-roll cross-rolling, rolling or extrusion. Squeeze after the tube diameter. Sizing machine through the high-speed rotation of the cone drill bit into the steel embryo drilling, the formation of steel pipe. The inner diameter of the pipe is determined by the outside diameter of the sizing bit. Steel pipe after sizing, into the cooling tower, through the water cooling, the cooling pipe, it is necessary to be straightened. After straightening by the steel pipe sent to the metal detector (or water pressure test) for internal testing. If the pipe has cracks, bubbles and other problems, will be detected. After the quality of steel pipe but also through rigorous manual selection. After the quality inspection of steel pipe, spray paint with the number, size, production lot number. And suspended by the crane into the warehouse.
Cold drawn (rolled) carbon steel seamless steel pipe: round tube → heating → punching → start → annealing → pickling → oiling (copper) → multi-pass cold drawing (cold rolling) → tube → heat treatment → straightening → water pressure test (testing) → marking → storage
Carbon steel seamless steel pipe because of its manufacturing process is different, is divided into hot-rolled (extrusion) seamless steel tubes and cold drawn (rolled) seamless steel pipe two. Cold drawn (rolled) tube is divided into two kinds of round tube and special-shaped tube.
In addition, GB / T17396-1998 (hot-rolled seamless steel pipe for hydraulic support), GB3093-1986 (diesel engine high-pressure seamless steel pipe), GB / T3639-1983 (cold drawn or cold-rolled precision seamless steel pipe), GB / T3094-1986 (cold drawn seamless steel pipe shaped steel pipe), GB / T8713-1988 (hydraulic and pneumatic cylinder with precision diameter seamless steel pipe), GB13296-1991 (boiler, heat exchanger with stainless steel seamless pipe), GB / T14975 (Seamless Steel Tube for Automotive Axle Bushings), API SPEC5CT-1999 (Casing and Tubing), GB / T14976-1994 (Seamless Steel Pipe for Fluid Conveying) Specification) and so on.
carbon steel pipe manufacturing
The raw material of carbon steel pipe is round pipe billet. The round pipe billet is cut by the cutting machine and processed into the billet with the length of 1 meter. And then sent to th furnace tobe heated by the conveyer belt. The billet is fed into a furnace and heated at a temperature of about 1200 degrees Celsius. The fuel is hydrogen or acetylene. Furnace temperature control is a key issue. After the round tube billet to go through the pressure piercing machine to wear empty. Generally more common punching machine is conical roller piercing machine, this punching machine production efficiency is high, product quality is good, perforation expansion diameter large, can wear a variety of steel. After piercing, the round tube blank has been three-roll cross-rolling, rolling or extrusion. Squeeze after the tube diameter. Sizing machine through the high-speed rotation of the cone drill bit into the steel embryo drilling, the formation of steel pipe. The inner diameter of the pipe is determined by the outside diameter of the sizing bit. Steel pipe after sizing, into the cooling tower, through the water cooling, the cooling pipe, it is necessary to be straightened. After straightening by the steel pipe sent to the metal detector (or water pressure test) for internal testing. If the pipe has cracks, bubbles and other problems, will be detected. After the quality of steel pipe but also through rigorous manual selection. After the quality inspection of steel pipe, spray paint with the number, size, production lot number. And suspended by the crane into the warehouse.
2016/12/07
Galvanized Steel Pipe
Galvanized steel pipe is the surface with hot-dip galvanized or electro-galvanized layer. Galvanized steel can increase corrosion resistance and prolong life. Galvanized steel pipe is widely used, except for water, gas, oil, generally low-pressure fluid line pipe, also used oil heater oil industry in particular, marine oil wells pipes, pipelines, chemical coking equipment, condensing coolers, washing coal distillate oil exchange used tubes, as well as the bridge piles, mine tunnel support frame with a pipe.
Galvanized steel pipe is divided into cold galvanized pipe and hot galvanized pipe, which is more extensive use of galvanized steel, hot galvanized steel is widely used in construction, machinery, mining, chemical, railway vehicles, the automotive industry, roads, bridges, container, sports facilities, agricultural machinery, petroleum machinery, prospecting machinery and other manufacturing industries. hot galvanized pipe is molten metal reacting with the iron matrix alloy layer, so that the substrate and coating combination of both. Galvanized pipe is first pickled, the steel surface in order to remove iron oxide, after pickling, cleaning tank by mixing an aqueous solution of ammonium chloride or zinc chloride and zinc chloride or ammonium chloride solution, and then into hot dip tank. Galvanized with coating uniformity, strong adhesion, long life and other advantages. Hot dip galvanized steel substrate with molten bath complicated physical, chemical reactions, the formation of corrosion-resistant zinc-iron alloy structure closely layer. Alloy layer and layer of pure zinc, steel base blend. Therefore it resistant to corrosion.
Shinestar chairman Guoyu Yi re-elected yueyang Representative of the Municipal People's Congress
Shinestar chairman Guoyu Yi re-elected yueyang Representative of the Municipal People's Congress
November 28th .Grand opening of the seventeenth people's Congress of Xiangyin County, Yueyang City.Shinestar chairman Guoyu YI was elected to the Yueyang Municipal People's Congress, this is Mr. Guoyu YI second award.
November 28th .Grand opening of the seventeenth people's Congress of Xiangyin County, Yueyang City.Shinestar chairman Guoyu YI was elected to the Yueyang Municipal People's Congress, this is Mr. Guoyu YI second award.
Yi Guoyu incumbent Shinestar Group Co., Ltd.Shinestar has been established since 1993.Yi Guoyu has always been a pragmatic entrepreneurial spirit of innovation and the trend of the times ahead of strategic decision pilot Shinestar .Shinestar has come out a way of development.Now the shinestar accumulate steadily.Owns 23 subsidiaries.China won the top 500 private enterprises.100 strong enterprises in Hunan Province.Created the Chinese steel pipe exports third.Hunan steel pipe sales of first outstanding achievements.At present, shinestar has set up in quality based production.To serve as a whole.Global trade as an engine for the improvement of the group platform.Has established the domestic "aircraft carrier grade" the status of the overall service provider of steel procurement.
As the entrepreneur, Guoyu Yi always think good thoughts , more actively involved in the construction of the city Xiangyin in Yueyang and thanksgiving return society. Both support the hometown construction, and to help nursing homes, laid-off workers, Guoyu Yi have special pure heart, holding the glorious cause tradition. Since 2012, he devoted to respect business, sponsored yueyang xiangyin many nursing homes; Support hometown construction, yueyang xiangyin tiejiaozui town highway construction project; Successively aid more than hunan steel market dealers, help them through struggling; More help more than 100 laid-off workers re-employment.
This term is the glory of Guoyu Yi and Shinestar of glory. Guoyu Yi said that he would collect public opinion, exert good NPC delegates responsibilities and advice for the development of yueyang city and xiangyin, render contribute their own. National People's Congress representative shall, on behalf of the interests of the people and will, in accordance with the law, exercise their functions and powers on behalf of the representative duty actively, give full play to their role as the representative. NPC delegates should close contact with the masses of the people, more frequent visit contact with voters, listen to and reflect their views and requirements, to serve the people. And all this is closely related to Shinestar business philosophy and mission, "internal achievements of employees, client, foreign achievement", its essence is to stand in the perspective of "people", thinking the management and development of the enterprise.
Finally, chairman of Guoyu Yi to concern for the development of party and government organs, enterprises and institutions, social people from all walks of life and the masses of customers, the most sincere thank you, thank you has long been a concern for ChengShi da, help, trust and support. Thanks everybody's care, give ChengShi of infinite strength and inspiration to Shinestar in building "steel overall service in the field of benchmarking enterprise" in one hundred and advance bravely .
2016/11/30
Prime set up tianjin branch, promote the development of international trade
On November 18, located in tianjin binhai zone at nankai huayuan industrial district science and technology building of hunan prime steel pipe LTD co.,tianjin branch officially opened. The new company will be relying on tianjin traffic advantages, as well as Shinestar production resources of tianjin production base, to further promote the development of Shinestar of iron steel group international trade, for the global customers with high quality steel products and services.
Shinestar CEO Wang Li and Hunan prime steel pipe co., LTD., general manager of publicity and tianjin branch, head of the relevant departments attended the ceremony and cut the ribbon for the new company.
It is understood that last year put into production of tianjin production base, is based on tianjin Shinestar of iron steel group, radiation global manufacturing platform, has been committed to the construction of high yield, good performance, the domestic first-class, international leading steel production base, and gradually grasp own advanced production technology, constantly meet the greater needs of customers and improve comprehensive competitiveness of the market. Powerful production base in tianjin will no doubt provide solid at tianjin prime branch security capacity, make the prime no trouble back at home, at pushing into the international market.
Shinestar of iron steel group are in the globalization development strategy phase, group subsidiary is oriented to the international market comprehensively, hunan prime steel pipe co., LTD., tianjin branch, is timely. At tianjin branch will focus on the layout in the Middle East, southeast Asia, Africa and parts of Europe and the United States and other international markets, provide dominated by straight seam welded pipe, synchronous provide seamless tube, spiral pipe and adapter tube of high quality products and perfect service.
Prime manager zhang said, at tianjin branch will continue adhering to the "good faith in mind, depends on the sincerity to win customers" work principle, to provide one-stop shopping service, professional team to meet customer the regulatory requirements of the project. Will also arrange all kinds of professionals in different links of supervision and monitoring, to ensure the high quality products to be produced.
As a world-class straight seam welded pipe production services suppliers, prime at committed to to the oil, gas, construction, energy and chemical industry, providing the quality are in conformity with price of steel pipe products, and always believe that effective communication, professional industry knowledge, rapid execution, lead the prime at with customers to establish long-term relations of cooperation.
Prime at belonging to Shinestar of iron steel group. As a base, service global production of large steel enterprises in China, Shinestar of domestic and international trade in 2016 double wave red, topped the top 100 enterprises of hunan. Its high quality steel products won a good market both at home and abroad. The future, Shinestar will toward building the "aircraft carrier" domestic steel procurement service as a whole and benchmarking enterprise's target for one hundred, and continuously.
Defects Of Welded Steel Pipe
Defects Of Welded Steel Pipe
Welded steel pipe production process is a steel sheet,strip,and other various molding methods using the straight press roll helical direction curling into a desired cross-sectional shape,and then by means of heart,prssure,different methods of welding weld weld together to obtain steel.Therefore,defects in the welded steel pipe is divided into two parts:the steel base material defects and weld defects.
1.Steel base material defect
The sheet material defects after rolling and other processes,most of planar,parallel to the surface;their main weakness delamination,cracks,folds,etc.,which is the most common layered internal defects.Stratification will produce a variety of cracks when the tensile stress perpendicular to the surface of the sheet by the hierarchical will seriously affect the strength of the steel pipe,it is not allowed defects.
2.Weld defects
Weld defects refers to defect during welding or after welding resulting in the weld is divided into cracks,proes,slag,incomplete penetration,incomplete fusion,undercut weld defects.Intensive weld porosity,slag,etc.a dense three-dimensional defects,cracks,lack of fusion and other defects in the case of the flat,great harm.Strip slag.
Welded steel pipe production process is a steel sheet,strip,and other various molding methods using the straight press roll helical direction curling into a desired cross-sectional shape,and then by means of heart,prssure,different methods of welding weld weld together to obtain steel.Therefore,defects in the welded steel pipe is divided into two parts:the steel base material defects and weld defects.
1.Steel base material defect
The sheet material defects after rolling and other processes,most of planar,parallel to the surface;their main weakness delamination,cracks,folds,etc.,which is the most common layered internal defects.Stratification will produce a variety of cracks when the tensile stress perpendicular to the surface of the sheet by the hierarchical will seriously affect the strength of the steel pipe,it is not allowed defects.
2.Weld defects
Weld defects refers to defect during welding or after welding resulting in the weld is divided into cracks,proes,slag,incomplete penetration,incomplete fusion,undercut weld defects.Intensive weld porosity,slag,etc.a dense three-dimensional defects,cracks,lack of fusion and other defects in the case of the flat,great harm.Strip slag.
2016/11/28
Corrosion Problems of ERW Steel Pipe
ERW steel pipe outer coating of the basic functions,there are two aspects:
First,make the ERW steel pipe surface from electrochemical corrosion,bacterial corrosion protection of soil basic physical media.
Second,resist the soil medium move creep stress,basic mechanical protection method static sterss and abrasion strength and structure and so on.
The basic principles of the outer coating selected city gas pipeline:
a,good insulation properties and mechaniacal properties;
b,good resistance to cathodic disbanding performance;
c,good resistance to water,gas permeability;
d,good chemical resistance properties of soaking and aging;
e,low tempercature and high temperature performance;
f,easy mending and mending;
g,the price is reasonable.
First,make the ERW steel pipe surface from electrochemical corrosion,bacterial corrosion protection of soil basic physical media.
Second,resist the soil medium move creep stress,basic mechanical protection method static sterss and abrasion strength and structure and so on.
The basic principles of the outer coating selected city gas pipeline:
a,good insulation properties and mechaniacal properties;
b,good resistance to cathodic disbanding performance;
c,good resistance to water,gas permeability;
d,good chemical resistance properties of soaking and aging;
e,low tempercature and high temperature performance;
f,easy mending and mending;
g,the price is reasonable.
2016/11/27
Iron and steel industry prices fell, the reason why?
As we all know, often drop large iron and steel industry, the price is extremely unstable, so what is the cause of this phenomenon?Shinestar Steel Research Institute found through research, technology and the characteristics of the iron and steel industry, the cost structure resulted in the imbalance between supply and demand environment quantity adjustment special difficulties.
Specifically, the characteristics of modern steel production technology determines that the industry has a strong scale effect.This means that the iron and steel enterprises need to spend a huge amount of money to buy equipment and equipment to build production systems, resulting in a higher proportion of fixed capital amortization of depreciation in the total cost.Shinestar Steel Group attaches great importance to R & D investment, its R & D production of carbon steel pipe, welded steel pipe, line pipe, galvanized pipe and other excellent products, the market was highly recognized.
Under normal market conditions, the characteristics of the industry makes the steel enterprises with the average cost per unit of output with the output scale and reduce the advantages, is conducive to enhancing the competitiveness of enterprises by expanding the scale, so the rapid growth in market demand under the environment of enterprises with strong expansion impulse.However, the demand for reverse change and under the conditions of excess capacity, the objective needs of sales compensation huge cost sharing, will lead to reduced production enterprises facing special difficulties,makes an ordinary enterprise may have to accept the price is far below the average cost, the formation of the iron and steel industry seems to be more willing to price competition and regardless of the loss of the phenomenon.
At present, the entire industry is under the background of the capacity to understand the difficulties behind the steel enterprises are more conducive to the promotion of structural adjustment.Huge amortization cost constraints, in addition to the mentioned steel blast furnace if stewing furnace boiler stop need extra pay huge cost, which further increased the steel mills production scale down the economic difficulties.In addition, the government protection measures from the Angle of system distortion may prevent enterprises from the number and scale down.
Requires industry to face the question is: in 2009, 460 million tons of crude steel production in China, in 2015 the actual production capacity of more than 1.25 billion tons of crude steel in our country, production of 804 million tons.By profit nature of the enterprise, industry concentration degree increase, corporate profitability increased, the influx of capital, capacity expansion again, a single merger can not limit production capacity expansion.
Product navigation, production escort,Shinestar Steel Group has been very focused on product development and production, which owns the layout of Changsha, Xiangyin, Nanchang, Tianjin four production bases,combined shinestar steel R & D and production of the powerful platform, R & D and production of carbon steel pipe, welded steel pipe, line pipe, galvanized pipe and other excellent products, praised by customers.The future, Shinestar will continue to increase investment, the introduction of advanced technology and equipment, the more the production of more and better quality products, in order to adapt to the development of the globalization strategy.
Specifically, the characteristics of modern steel production technology determines that the industry has a strong scale effect.This means that the iron and steel enterprises need to spend a huge amount of money to buy equipment and equipment to build production systems, resulting in a higher proportion of fixed capital amortization of depreciation in the total cost.Shinestar Steel Group attaches great importance to R & D investment, its R & D production of carbon steel pipe, welded steel pipe, line pipe, galvanized pipe and other excellent products, the market was highly recognized.
Under normal market conditions, the characteristics of the industry makes the steel enterprises with the average cost per unit of output with the output scale and reduce the advantages, is conducive to enhancing the competitiveness of enterprises by expanding the scale, so the rapid growth in market demand under the environment of enterprises with strong expansion impulse.However, the demand for reverse change and under the conditions of excess capacity, the objective needs of sales compensation huge cost sharing, will lead to reduced production enterprises facing special difficulties,makes an ordinary enterprise may have to accept the price is far below the average cost, the formation of the iron and steel industry seems to be more willing to price competition and regardless of the loss of the phenomenon.
At present, the entire industry is under the background of the capacity to understand the difficulties behind the steel enterprises are more conducive to the promotion of structural adjustment.Huge amortization cost constraints, in addition to the mentioned steel blast furnace if stewing furnace boiler stop need extra pay huge cost, which further increased the steel mills production scale down the economic difficulties.In addition, the government protection measures from the Angle of system distortion may prevent enterprises from the number and scale down.
Requires industry to face the question is: in 2009, 460 million tons of crude steel production in China, in 2015 the actual production capacity of more than 1.25 billion tons of crude steel in our country, production of 804 million tons.By profit nature of the enterprise, industry concentration degree increase, corporate profitability increased, the influx of capital, capacity expansion again, a single merger can not limit production capacity expansion.
Product navigation, production escort,Shinestar Steel Group has been very focused on product development and production, which owns the layout of Changsha, Xiangyin, Nanchang, Tianjin four production bases,combined shinestar steel R & D and production of the powerful platform, R & D and production of carbon steel pipe, welded steel pipe, line pipe, galvanized pipe and other excellent products, praised by customers.The future, Shinestar will continue to increase investment, the introduction of advanced technology and equipment, the more the production of more and better quality products, in order to adapt to the development of the globalization strategy.
2016/11/24
The difference between ERW pipe and HFW pipe
The difference between ERW pipe and HFW pipe
ERW call is one of the resistance welding steel pipe, ERW are respectively corresponding to the first letter of the English word. Resistance welding steel pipe can be divided into ac and dc welding welding two forms.
Ac welding according to the different frequency is divided into low frequency, intermediate frequency brazing, intermediate frequency and high frequency welding welding. High frequency welding is mainly used for thin wall pipe or ordinary wall thickness pipe production, high frequency welding is divided into contact welding and induction welding.
Dc welding is commonly used in small diameter steel pipe.
So, in general, the high frequency welded pipe contained in ERW welded pipe, is a kind of high frequency welding process production ERW welded pipe.
ERW call is one of the resistance welding steel pipe, ERW are respectively corresponding to the first letter of the English word. Resistance welding steel pipe can be divided into ac and dc welding welding two forms.
Ac welding according to the different frequency is divided into low frequency, intermediate frequency brazing, intermediate frequency and high frequency welding welding. High frequency welding is mainly used for thin wall pipe or ordinary wall thickness pipe production, high frequency welding is divided into contact welding and induction welding.
Dc welding is commonly used in small diameter steel pipe.
So, in general, the high frequency welded pipe contained in ERW welded pipe, is a kind of high frequency welding process production ERW welded pipe.
2016/11/23
Price Adjustment for Q345 Welded Carbon Steel Pipe
Price Adjustment for Q345 Welded Carbon Steel Pipe
The focus of the current market or gathered in the social stock of Q345B longitudinal welded pipe, the five statistics on Friday the total inventory of the five Q345B longitudinal welded pipe stock total 8.44 million tons, 0.4% WoW, down 9.2%; five Q345B straight seam Weld pipe plant inventory total of 4.899 million tons, an increase of 4.9% WoW, down 16.3% year on year. If you look at the current social stock of Q345B longitudinal welded pipe absolute quantity, there is no doubt that the current market inventory pressure is small, but the steel plant inventory began to rise is worth noting. Because the five major varieties of social stock as a result of the decline in the sample caliber representative, in fact, outside the caliber of the amount of resources or trends in the trend of the sample is not the same, so the process of resource dispersion trend is often the core regional stock transfer to non-core areas .
In addition, as the "car limit set" strictly enforced, in fact, the increase in the amount of in-transit resources have been ignored, taking into account the limited capacity of vehicles in southern China, for example, motor transport cycle basically from the past 1-2 days to 2-5 days , That is, the amount of vehicles in transit than in the past to look through; the same token, in the original fuel materials also exist such a situation. If the vehicle capacity does not improve, this resource does not constitute a pressure on the market, but this year, truck sales rose significantly, from January to October 2016 more than 40 tons of semi-tractor sales rose 98.5%; 25-40 tons between the semi-traction Car sales rose 16.6%; 25 tons and below semi-tractor sales rose 119% year on year.
But in October, more than 40 tons, 25-45 tons and 25 tons the following semi-tractor sales were up 45.9%, 68.4% and 117.8%. In general, the truck sales to the road takes 50 days or so, once the capacity to enhance, ask who is willing to increase the transport cycle to extend and bear the burden of resources and risk of funds in transit, then the latter is not there will be a lot of transit resources into social stock To be tested!
Raw materials, the domestic coal mine production safety requirements more stringent, the major domestic coal mines to ensure safe production, production than the previous period have different degrees of decline, making most of the coking plant inventory of refined coal declined support coking coal prices continue to be strong . Affected by this, high-grade iron ore spot prices are also supported, the current futures and spot basis also reflects this trend. So hope that the original fuel material spot fell may not be desirable, but rather need to pay attention to the price difference between the repair. Of course, this premise is the production of steel production enterprises will not substantially
cut.
The focus of the current market or gathered in the social stock of Q345B longitudinal welded pipe, the five statistics on Friday the total inventory of the five Q345B longitudinal welded pipe stock total 8.44 million tons, 0.4% WoW, down 9.2%; five Q345B straight seam Weld pipe plant inventory total of 4.899 million tons, an increase of 4.9% WoW, down 16.3% year on year. If you look at the current social stock of Q345B longitudinal welded pipe absolute quantity, there is no doubt that the current market inventory pressure is small, but the steel plant inventory began to rise is worth noting. Because the five major varieties of social stock as a result of the decline in the sample caliber representative, in fact, outside the caliber of the amount of resources or trends in the trend of the sample is not the same, so the process of resource dispersion trend is often the core regional stock transfer to non-core areas .
In addition, as the "car limit set" strictly enforced, in fact, the increase in the amount of in-transit resources have been ignored, taking into account the limited capacity of vehicles in southern China, for example, motor transport cycle basically from the past 1-2 days to 2-5 days , That is, the amount of vehicles in transit than in the past to look through; the same token, in the original fuel materials also exist such a situation. If the vehicle capacity does not improve, this resource does not constitute a pressure on the market, but this year, truck sales rose significantly, from January to October 2016 more than 40 tons of semi-tractor sales rose 98.5%; 25-40 tons between the semi-traction Car sales rose 16.6%; 25 tons and below semi-tractor sales rose 119% year on year.
But in October, more than 40 tons, 25-45 tons and 25 tons the following semi-tractor sales were up 45.9%, 68.4% and 117.8%. In general, the truck sales to the road takes 50 days or so, once the capacity to enhance, ask who is willing to increase the transport cycle to extend and bear the burden of resources and risk of funds in transit, then the latter is not there will be a lot of transit resources into social stock To be tested!
Raw materials, the domestic coal mine production safety requirements more stringent, the major domestic coal mines to ensure safe production, production than the previous period have different degrees of decline, making most of the coking plant inventory of refined coal declined support coking coal prices continue to be strong . Affected by this, high-grade iron ore spot prices are also supported, the current futures and spot basis also reflects this trend. So hope that the original fuel material spot fell may not be desirable, but rather need to pay attention to the price difference between the repair. Of course, this premise is the production of steel production enterprises will not substantially
2016/11/22
Spiral steel pipe, straight seam steel pipe, steel springboard be better progressly
Spiral steel pipe, straight seam steel pipe, steel springboard be better progressly
The situation of the steel market this year is different from previous, traditional demand off-season arrival did not cause too big effect, because of the influence of the low costs and inventory, steel price short-term downside is limited, can predict early November steel prices fly again for a while! As a result, the spiral steel pipe, straight seam steel pipe, steel springboard products prices are going.
Steel market supply and demand in November there was still hope keep good posture, basically have the following reasons:
1, the capacity factor
Recent provinces to work in production on the agenda, on October 29, held in tangshan dissolve excess steel production capacity in October on demolishing, finished the province up to dissolve the steel production tasks this year. Operation, were dismantled the plump, qianan 8 companies nine four of converter or blast furnace burden, dissolve the ironmaking production capacity 4.83 million tons of steel production capacity of 2.9 million tons. Released parts factory shut down after the blast furnace, and the overall out of billet quantity reduced, already in short supply of billet is more short, cause certain influence to the stock.
2, inventory factors
In early October steel inventory and social inventory has fallen sharply, stock fell 113.3 and 902000 tons respectively, to the end of the month continues to decline, infinite close to historic lows. Look from the supply, according to the latest statistics, 164 tangshan steel blast furnace capacity utilization is 76.83%, weeks than fell by 4.88%, with the capacity to further fall to the ground, the development of the environmental supervision, the steel mills cut production maintenance, strained November will exacerbate, balance between supply and demand will be phased order.
3, cost factors,
Considering the steel mills coal, coke available inventory days continues to decline, some even only enough to use two or three days, the supply is still tight, there is a slight upward space; in November Catch up market also appears under its impetus, iron ore imports ore in October index gained about $10 / ton, this will encourage steel costs continue to rise. According to ChengShi of iron and steel group, data statistics, as of November 1, the average profit level of the thread is about 70 yuan/ton, profile is still losing money, the average losses of 30 yuan/tons, in social inventory and steel inventories are not high, steel sales, pressure is not big, the high cost can support steel prices continue to strong.
4, macro stabilizing factor
Obvious signs of macroeconomic stabilisation, demand for steel has had a huge impact. September PPI rebounded 0.5%, rose 0.1%, ended 54 months continue to fall. Due to higher commodity prices, laid the foundation for the expansion of enterprise management and earnings upgrades. Three is the enterprise profit improvement. Industrial enterprises above designated size 9 month before total profit year-on-year growth of 8.4%, 2.2% faster than the first half, 7-15.2% growth in August, September state profit up 27% from a year earlier. Corporate earnings improve, provides the power source for promoting investment. Both investment stabilized, and improve corporate profits, were supportive of steel consumption.
To sum up, the steel market in November, the cost and the influence of low inventory, downward space is limited, but, after all, the off-season fell to demand will continue to fall, the extent of upward will also be limited. Taken together, the probability of strong operation is higher, spiral steel pipe, straight seam steel pipe, steel springboard product prices will still be better progressly.
The situation of the steel market this year is different from previous, traditional demand off-season arrival did not cause too big effect, because of the influence of the low costs and inventory, steel price short-term downside is limited, can predict early November steel prices fly again for a while! As a result, the spiral steel pipe, straight seam steel pipe, steel springboard products prices are going.
Steel market supply and demand in November there was still hope keep good posture, basically have the following reasons:
1, the capacity factor
Recent provinces to work in production on the agenda, on October 29, held in tangshan dissolve excess steel production capacity in October on demolishing, finished the province up to dissolve the steel production tasks this year. Operation, were dismantled the plump, qianan 8 companies nine four of converter or blast furnace burden, dissolve the ironmaking production capacity 4.83 million tons of steel production capacity of 2.9 million tons. Released parts factory shut down after the blast furnace, and the overall out of billet quantity reduced, already in short supply of billet is more short, cause certain influence to the stock.
2, inventory factors
In early October steel inventory and social inventory has fallen sharply, stock fell 113.3 and 902000 tons respectively, to the end of the month continues to decline, infinite close to historic lows. Look from the supply, according to the latest statistics, 164 tangshan steel blast furnace capacity utilization is 76.83%, weeks than fell by 4.88%, with the capacity to further fall to the ground, the development of the environmental supervision, the steel mills cut production maintenance, strained November will exacerbate, balance between supply and demand will be phased order.
3, cost factors,
Considering the steel mills coal, coke available inventory days continues to decline, some even only enough to use two or three days, the supply is still tight, there is a slight upward space; in November Catch up market also appears under its impetus, iron ore imports ore in October index gained about $10 / ton, this will encourage steel costs continue to rise. According to ChengShi of iron and steel group, data statistics, as of November 1, the average profit level of the thread is about 70 yuan/ton, profile is still losing money, the average losses of 30 yuan/tons, in social inventory and steel inventories are not high, steel sales, pressure is not big, the high cost can support steel prices continue to strong.
4, macro stabilizing factor
Obvious signs of macroeconomic stabilisation, demand for steel has had a huge impact. September PPI rebounded 0.5%, rose 0.1%, ended 54 months continue to fall. Due to higher commodity prices, laid the foundation for the expansion of enterprise management and earnings upgrades. Three is the enterprise profit improvement. Industrial enterprises above designated size 9 month before total profit year-on-year growth of 8.4%, 2.2% faster than the first half, 7-15.2% growth in August, September state profit up 27% from a year earlier. Corporate earnings improve, provides the power source for promoting investment. Both investment stabilized, and improve corporate profits, were supportive of steel consumption.
To sum up, the steel market in November, the cost and the influence of low inventory, downward space is limited, but, after all, the off-season fell to demand will continue to fall, the extent of upward will also be limited. Taken together, the probability of strong operation is higher, spiral steel pipe, straight seam steel pipe, steel springboard product prices will still be better progressly.
2016/11/20
Galvanized Steel Pipe Using Advantages
Galvanized Steel Pipe Using Advantages
When we talk about the galvanized steel pipes, we usually refer to the hot dipped galvanized steels pipes which are more durable and strengthened than any other types. The cleaning process which the hot dipped galvanized steel pipe uses is far more special in the combination use of the solutions, including the ammonium chloride, zinc chloride or the mixed solutions of both. And it will be sent into the hot dipped groove afterwards. The galvanized steel tube will be with more even layer of the galvanization and the capacity of cohesion, anti-corrosion and anti-dust. All of these as mentioned above will contribute to this kind of steel pipe to be have longer longevity than any other steel pipe kinds.
The regular specification of the galvanized steel tubing which are available from SHINESTAR include 48.3×2.5、48.3×2.75、48.3×3.0、48.3×3.25、48.3×3.5 and other customized types per required.
To maintain these galvanized steel tubes, we should keep in mind about these following steps:
1. Regular clean away the piling-up materials around the steel and control its loading under its limitation.
2. Regular observe if there is any deviation among the steel tube's whole structure of parts of it. If yes, make alteration in time.
When we talk about the galvanized steel pipes, we usually refer to the hot dipped galvanized steels pipes which are more durable and strengthened than any other types. The cleaning process which the hot dipped galvanized steel pipe uses is far more special in the combination use of the solutions, including the ammonium chloride, zinc chloride or the mixed solutions of both. And it will be sent into the hot dipped groove afterwards. The galvanized steel tube will be with more even layer of the galvanization and the capacity of cohesion, anti-corrosion and anti-dust. All of these as mentioned above will contribute to this kind of steel pipe to be have longer longevity than any other steel pipe kinds.
The regular specification of the galvanized steel tubing which are available from SHINESTAR include 48.3×2.5、48.3×2.75、48.3×3.0、48.3×3.25、48.3×3.5 and other customized types per required.
To maintain these galvanized steel tubes, we should keep in mind about these following steps:
1. Regular clean away the piling-up materials around the steel and control its loading under its limitation.
2. Regular observe if there is any deviation among the steel tube's whole structure of parts of it. If yes, make alteration in time.
2016/11/17
Advantages of welded pipe
Advantages of welded pipe
Structural welded pipe (tubing) can be used for a wide variety of mechanical applications. It may be used either statically or dynamically. Its close tolerances, good finish, and dense structure make it ideal for parts such as structural support and parts, frames, racks, trailer beds and trailer components, structural components and supports for buildings, bridges, and highways, conveyors, machine parts, ornamental usages and a wide range of applications in industrial, construction, automotive, appliance and agricultural industries.
Welded pipes are generally more cost effective than the equivalent seamless alternative. They are significantly more available both from distributor and mill stocks and from a mill production lead time perspective. With longer lead times seamless tubes can be exposed to unknown alloying price extras that can fluctuate substantially, hence it can be difficult to plan and predict the true costs for the material. Therefore in addition to faster delivery times for Erw tubes, there is the added advantage of lower economical risk. Erw welded steel tubes generally have better surface quality as compared with manufacturing seamless tubes. Seamless tubes are generally made in multiple steps starting with hot extrusion to form the tube hollows from billets.
Structural welded pipe (tubing) can be used for a wide variety of mechanical applications. It may be used either statically or dynamically. Its close tolerances, good finish, and dense structure make it ideal for parts such as structural support and parts, frames, racks, trailer beds and trailer components, structural components and supports for buildings, bridges, and highways, conveyors, machine parts, ornamental usages and a wide range of applications in industrial, construction, automotive, appliance and agricultural industries.
Welded pipes are generally more cost effective than the equivalent seamless alternative. They are significantly more available both from distributor and mill stocks and from a mill production lead time perspective. With longer lead times seamless tubes can be exposed to unknown alloying price extras that can fluctuate substantially, hence it can be difficult to plan and predict the true costs for the material. Therefore in addition to faster delivery times for Erw tubes, there is the added advantage of lower economical risk. Erw welded steel tubes generally have better surface quality as compared with manufacturing seamless tubes. Seamless tubes are generally made in multiple steps starting with hot extrusion to form the tube hollows from billets.
2016/11/16
Austenitic Stainless Steel
Austenitic Stainless Steel
Low carbon, iron-chromium-nickel stainless alloys containing more than 16% chromium, and 4 to 22% nickel to provide an austenitic structure at normal temperatures. These alloys cannot be hardened by heat treatment, but can be hardened by cold working. They are normally non-magnetic in the annealed condition, but can become slightly magnetic after cold working depending upon composition.
Austenitic Stainless Steel Pipe
Austenitic stianless steel pipe recers to the normal temperature of austenitc stianless steel containing about 18% of Cr, 8%~10% of Ni, 0.1% of C and a stable austenite. Austenitic chrome nickel stianless steel pipe including the famous 18Cr-8Ni steel. On this basis to increase the Cr, Ni content and adding Mo, Cu, Si, Nb, Ti and other elements developed high Cr-Ni series of steel pipe. Austenitic stainless steel pipe is non-meganetic and has high toughness and plasticity. However, the strength of austenitic stainless steel pipe is low which can not be strengthened by phase transformation and can only be strengthened by cold working, such as addign S, Ca, Se, Te and other elements which has a good easing cutting characteristic.
Low carbon, iron-chromium-nickel stainless alloys containing more than 16% chromium, and 4 to 22% nickel to provide an austenitic structure at normal temperatures. These alloys cannot be hardened by heat treatment, but can be hardened by cold working. They are normally non-magnetic in the annealed condition, but can become slightly magnetic after cold working depending upon composition.
Austenitic Stainless Steel Pipe
Austenitic stianless steel pipe recers to the normal temperature of austenitc stianless steel containing about 18% of Cr, 8%~10% of Ni, 0.1% of C and a stable austenite. Austenitic chrome nickel stianless steel pipe including the famous 18Cr-8Ni steel. On this basis to increase the Cr, Ni content and adding Mo, Cu, Si, Nb, Ti and other elements developed high Cr-Ni series of steel pipe. Austenitic stainless steel pipe is non-meganetic and has high toughness and plasticity. However, the strength of austenitic stainless steel pipe is low which can not be strengthened by phase transformation and can only be strengthened by cold working, such as addign S, Ca, Se, Te and other elements which has a good easing cutting characteristic.
2016/11/15
SAE/AMS Specifications Sheet
SAE/AMS Specifications Sheet
SAE-J356 Welded Flash Controlled Low Carbon Steel Tubing Normalized for Bending. Double Flaring and Beading.
Covers normalized electric resistance welded tube ID flash-controlled .005" to .010" manipulative quality.
SAE-J524 Seamless Low Carbon Steel Tubing Annealed for Bending and Flaring.
Covers cold drawn seamless JIC hydraulic line tubing.
SAE-J525 Welded and Drawn Low Carbon Steel Tubing Annealed for Bending and Flaring.
Covers welded and drawn JIC hydraulic line tubing.
SAE-J526 Welded Low Carbon Steel Tubing.
Covers annealed welded tube with ID flash-in for general automotive applications.
SAE-J527 Brazed Double Wall Carbon Steel Tubing.
Covers copper brazed double wall low carbon steel tube intended for general automotive applications and other similar uses. Suitable for bending, forming and double flaring.
SAE-J529 Fuel Injection Tubing.
Covers low carbon steel tube specially manufactured for high pressure fuel injection lines for diesel engines.
AMS-5050 Seamless Annealed Low Carbon Steel Tube.
Covers cold drawn seamless JIC hydraulic line steel tubing for aircraft applications.
AMS-5062 Seamless Low Carbon Steel Tube.
Covers cold finished or hot finished seamless low carbon mechanical steel tube.
AMS-6360 Seamless SAE 4130 Alloy Steel Tubing.
Covers aircraft quality 4130 tube in condition N temper. Similar to MIL-T-6736 specification.
AMS-6365 Seamless SAE 4135 Alloy Steel Tubing.
Covers aircraft quality 4135 tube in condition N temper. Similar to MIL-T-6735 specification.
AMS-6371 Seamless SAE 4130 Alloy Steel Mechanical Tubing.
Covers electric furnace grade magnaflux quality 4130 aircraft tube, either hot finished or cold finished, hardenable.
AMS-6372 Seamless SAE 4135 Alloy Steel Mechanical Tubing.
Covers electric furnace grade magnaflux quality 4135 aircraft tube, either hot finished or cold finished, hardenable.
AMS-6381 Seamless SAE 4140 Alloy Steel Mechanical Tubing.
Covers electric furnace grade magnaflux quality 4140 aircraft tube, either hot finished or cold finished, hardenable.
AMS-6415 Seamless SAF 4340 Alloy Steel Mechanical Tubing.
Covers electric furnace grade magnaflux quality 4340 aircraft tube, either hot finished or cold finished, hardenable.
SAE-J356 Welded Flash Controlled Low Carbon Steel Tubing Normalized for Bending. Double Flaring and Beading.
Covers normalized electric resistance welded tube ID flash-controlled .005" to .010" manipulative quality.
SAE-J524 Seamless Low Carbon Steel Tubing Annealed for Bending and Flaring.
Covers cold drawn seamless JIC hydraulic line tubing.
SAE-J525 Welded and Drawn Low Carbon Steel Tubing Annealed for Bending and Flaring.
Covers welded and drawn JIC hydraulic line tubing.
SAE-J526 Welded Low Carbon Steel Tubing.
Covers annealed welded tube with ID flash-in for general automotive applications.
SAE-J527 Brazed Double Wall Carbon Steel Tubing.
Covers copper brazed double wall low carbon steel tube intended for general automotive applications and other similar uses. Suitable for bending, forming and double flaring.
SAE-J529 Fuel Injection Tubing.
Covers low carbon steel tube specially manufactured for high pressure fuel injection lines for diesel engines.
AMS-5050 Seamless Annealed Low Carbon Steel Tube.
Covers cold drawn seamless JIC hydraulic line steel tubing for aircraft applications.
AMS-5062 Seamless Low Carbon Steel Tube.
Covers cold finished or hot finished seamless low carbon mechanical steel tube.
AMS-6360 Seamless SAE 4130 Alloy Steel Tubing.
Covers aircraft quality 4130 tube in condition N temper. Similar to MIL-T-6736 specification.
AMS-6365 Seamless SAE 4135 Alloy Steel Tubing.
Covers aircraft quality 4135 tube in condition N temper. Similar to MIL-T-6735 specification.
AMS-6371 Seamless SAE 4130 Alloy Steel Mechanical Tubing.
Covers electric furnace grade magnaflux quality 4130 aircraft tube, either hot finished or cold finished, hardenable.
AMS-6372 Seamless SAE 4135 Alloy Steel Mechanical Tubing.
Covers electric furnace grade magnaflux quality 4135 aircraft tube, either hot finished or cold finished, hardenable.
AMS-6381 Seamless SAE 4140 Alloy Steel Mechanical Tubing.
Covers electric furnace grade magnaflux quality 4140 aircraft tube, either hot finished or cold finished, hardenable.
AMS-6415 Seamless SAF 4340 Alloy Steel Mechanical Tubing.
Covers electric furnace grade magnaflux quality 4340 aircraft tube, either hot finished or cold finished, hardenable.
The Safe Ways to Use Scaffolding System and Tubes
In high-rise building construction, every step outside the frame to be paved with bamboo basketry or steel fabric, in addition to deaden 1 m high railing and standing bamboo basketry board. On the outer edge of the scaffold, set up safety set net.
Second, the floor protection measures. Now most of the high-rise buildings are concrete frame constructions, widespread adoption MS pipe scaffolding support steel formwork construction. In order to do the protection of the floor construction, can use floor frame. Guard is equal to the height of the two floors of the building, protecting frame width is equivalent to the length of the building a studio.(floor care on the scaffolding tube can prevent falling to the lateral personnel construction, can also be used as a construction safety channel.)
Three, floor slanted protective measures Some concrete frame building, caused by a lack of hoisting equipment, inconvenient installation floor frame, using steel formwork support. Preferably in the surrounding buildings, the erection slanted plane, vertical height and construction of building height, the same set-up of ledger, carry on oblique one safety net. (the floor is slanted frame, also can prevent the staff falling to the outside, but in the build-up to pick frame, workers have to switch seat belt) four, socket frame protection measures.
Some high-rise building, using the plug in or the ingate cast-in-place reinforced concrete shear wall construction method, in order to ensure the safety of construction personnel. Tool type socket frame can be used, the height of the socket frame over a layer of floor, can prevent the construction layer surrounding the staff fall outward.
Second, the floor protection measures. Now most of the high-rise buildings are concrete frame constructions, widespread adoption MS pipe scaffolding support steel formwork construction. In order to do the protection of the floor construction, can use floor frame. Guard is equal to the height of the two floors of the building, protecting frame width is equivalent to the length of the building a studio.(floor care on the scaffolding tube can prevent falling to the lateral personnel construction, can also be used as a construction safety channel.)
Three, floor slanted protective measures Some concrete frame building, caused by a lack of hoisting equipment, inconvenient installation floor frame, using steel formwork support. Preferably in the surrounding buildings, the erection slanted plane, vertical height and construction of building height, the same set-up of ledger, carry on oblique one safety net. (the floor is slanted frame, also can prevent the staff falling to the outside, but in the build-up to pick frame, workers have to switch seat belt) four, socket frame protection measures.
Some high-rise building, using the plug in or the ingate cast-in-place reinforced concrete shear wall construction method, in order to ensure the safety of construction personnel. Tool type socket frame can be used, the height of the socket frame over a layer of floor, can prevent the construction layer surrounding the staff fall outward.
2016/11/13
Vietnam steel industry has high growth potential
According to the Viet Nam Steel Association, the country's steel industry has great development potential. Speaking at a seminar titled "Viet Nam's steel industry – rise and fall and development potential" in HCM City on Monday, Dr Nguyen Van Sua the association's vice chairman said that per capita consumption in Viet Nam is 200kg, below the world average of 216kg. he said that "In an industrialised economy, the per capita consumption ranges from 500kg to 600kg."
2016/11/10
Petro China and Malaysia has sighed Sabah Natural Gas Pipeline Project
On the afternoon of November 1, 2016, under the witness of Premier Li Keqiang and Malaysian Prime Mnister Najib Razak, The deputy general manageer of China National Petroleum Corporation (CNPC) Liu Hongbin and the Chairman of Strategic Energy Co., Ltd of Sulia Mohammad Evan Seriga Abu, on behalf of the two companies, have dual signed the Contract for the Construction and Trail Operation of Sabah Gas Pipeline Project and the Contract for Construction and Commissioning of Multu-medium Pipeline Project in Beijing.
Sabah gas pipeline and multi-media pipeline is the Malaysian federal government-led projects. Under the agreement, China Petroleum Pipeline Bureau will EPCC way to undertake the construction of these two pipeline projects.
Sabah gas pipeline and multi-media pipeline is the Malaysian federal government-led projects. Under the agreement, China Petroleum Pipeline Bureau will EPCC way to undertake the construction of these two pipeline projects.
In Stock ERW Steel Pipe Price 2016/11/11
| API 5L/A53 GR.B, ERW Steel Pipe, Carbon Steel | ||||||
| Outside Diameter | Wall Thickness | Length | Quantity 数量 | Remark 标记 | EXW CHINA 出厂价 | |
| 外径 (mm) | 壁厚 (mm) | 长度 (mtr) | PCS 根数 | TON 吨位 | Surface,End | USD/TON 美金每吨 |
| 168.3 | 7.5 | 5.8 | 50 | 14.24 | BE. BARE | $515.82 |
| 355.6 | 6.8 | 6.5 | 75 | 10.86 | BE. BARE | $546.80 |
| 508.0 | 13.0 | 12 | 6 | 2.94 | BE. BARE | $560.27 |
| 114.3 | 9.5 | 6 | 30 | 14.30 | BE. BARE | $583.16 |
| 273.0 | 8.5 | 11.8 | 30 | 54.91 | BE. BARE | $518.52 |
| 139.7 | 4.9 | 6.5 | 23 | 2.55 | BE. BLACK | $507.74 |
| 219.1 | 10.5 | 6 | 56 | 22.20 | BE. BLACK | $531.99 |
| 273.0 | 9.3 | 12 | 23 | 17.04 | BE. BLACK | $523.91 |
| 355.6 | 12.7 | 6 | 30 | 13.10 | BE. BLACK | $565.66 |
| 406.4 | 6.4 | 12 | 70 | 40.75 | BE. BLACK | $552.19 |
| 33.4 | 3.5 | 6 | 132 | 2.04 | BLACK | $504.62 |
| 48.3 | 4.25 | 6 | 56 | 1.55 | BLACK | $516.92 |
| 73 | 5.5 | 6 | 42 | 2.31 | BLACK | $523.76 |
| 76.1 | 5.5 | 6 | 110 | 6.32 | BE. BLACK | $521.03 |
| 108 | 6.5 | 6 | 59 | 5.76 | BLACK | $552.48 |
| 127 | 5.6 | 6 | 73 | 7.34 | BE. BLACK | $501.48 |
| 133 | 7.7 | 6 | 142 | 20.27 | BLACK | $493.68 |
| 152 | 4.3 | 6 | 230 | 21.61 | BE. BLACK | $497.48 |
| 165 | 6.0 | 6 | 114 | 16.09 | BE. BLACK | $505.98 |
| 168.3 | 3.5 | 6 | 165 | 14.08 | BLACK | $490.94 |
| 26.7 | 2.87 | 6.1 | 198 | 2.04 | BLACK | $507.94 |
| 42.2 | 3.56 | 6 | 345 | 7.02 | BLACK | $498.58 |
| 48.3 | 3.7 | 5.8 | 129 | 3.03 | BLACK | $489.22 |
| 33.4 | 3.9 | 5.8 | 432 | 7.12 | BE. BLACK | $489.22 |
| 73 | 3.4 | 5.8 | 368 | 12.39 | BE. BLACK | $498.58 |
| 159 | 6.0 | 6.1 | 123 | 16.99 | BE. BLACK | $481.20 |
| 273 | 9.3 | 6.1 | 301 | 110.70 | BE. BLACK | $514.62 |
| 133 | 6.5 | 5.8 | 220 | 25.87 | BE. BLACK | $485.21 |
| 178 | 8.0 | 5.8 | 206 | 40.07 | BE. BLACK | $491.90 |
| 168.3 | 7.1 | 6 | 188 | 31.88 | BE. BLACK | $490.56 |
| Note: 1. The above price is based on bare pipe, for extra coating, please contact sales@primesteeltube.com; | ||||||
| 2. The above price is based on EXW, for FOB/CIF/CFR price, please contact sales@primesteeltube.com; | ||||||
| 3. The above price is not including any packing and end processing charge, for detailed quotation, please contact sales@primesteeltube.com; | ||||||
| 4. The above price is only valide during NOV 11- 18; | ||||||
| 5. The applicapable MOQ for this price list is over 25 tons; | ||||||
Subscribe to:
Posts (Atom)